Warewashing green&clean dual rinse rack type, Energy Saving Device,ZERO LIME,Wash-Safe Control 250r/h, elec-50Hz (COD 535107)

Compare Where to buy

Dual Rinse Rack Type dishwashers - 250 racks per hour

Warewashing
green&clean dual rinse rack type, Energy Saving Device,ZERO LIME,Wash-Safe Control 250r/h, elec-50Hz

COD 535107

Dual rinse rack type dishwasher, 250 racks/hour, Energy Saving Device, ZERO LIME Device, CLEAR BLUE Filtering System, WASH-SAFE CONTROL, electric, touch screen, Left>Right

Compare

Where to buy

Specifications

Air Emission

Air humidity (top, exit): 100 / 0 % r.h.

Latent heat: 5000 W

Sensible heat: 3500 W

Air flow (top, exit): 565 / 0 m³/h

Air temperature (top, exit): 27 °C

The data is measured at exhaust points at 25°C and 60% r.h. ambient conditions, 18°C inlet water temperature and refer only to the machine.

This model requires a ventilation hood. Please refer to the attached "Recommended Exhaust Hood Design".
Electric

When the machine is run at DIN 10510 compliant speed.

Pre-wash tank heating element are activated only during sanitation cycle.

Wash pump size: 1.5kW

Supply voltage: 380-415 V/3N ph/50 Hz

Pre-wash tank heating elements: 7 kW

Default Installed Power: 33 kW

Boiler heating elements: 19 kW

Electrical power, min: 23 kW

Wash tank heating elements: 10 kW
Water

Inlet cold water line size: G 3/4"

When below 7°fH/4°dH special detergent and rinse aid are needed.

Peak rate of drain flow: 2.5 l/s

Pre-wash tank size: 70 l

Inlet hot water line size: G 3/4"

Drain line size: 50mm

Inlet water supply pressure: 1.5-6 bar

Inlet water supply temperature (wash): 50 - 65 °C

Inlet water supply hardness: 14 °fH / 8°dH

Water cold/hot pipe size G 3/4"
Key Information

For transportation purpose only, the depth can be reduced to either 895mm by removing the main switch button or 797mm by removing the control box and the door handle.

Reference norm used to measure the noise: IEC60335-2-58 annex AA.

Table to table distance: 2010 mm

Height with door open: 2095 mm

Charging hole size (width): 530 mm

Productivity per hour (max. speed): 250 racks/4500dishes

Productivity per hour (medium speed): 168 racks/3024 dishes

External dimensions, Width: 2410 mm

External dimensions, Depth: 925 mm

External dimensions, Height: 1908 mm

Productivity per hour (DIN compliant speed): 115 racks/2070 dishes

Charging hole size (height): 490 mm

Wash Temperature: 55 - 65 °C

Shipping height: 2068 mm

Shipping width: 1006 mm

Shipping depth: 2142 mm

Shipping volume: 4.46 m³

Pre-wash temperature: 10-40°C

Final rinse temperature: 85 °C
Sustainability

Rinse water consumption at max speed (l/rack): 1 l/rack

Rinse water consumption at max speed (l/h) 250 l/h

Noise level: <62 dBA

Documents

Product Features

Main Features

IP25 protection against water jets, solid objects and small animals (larger than 6 mm).

Adjustable feet for full access underneath the machine for cleaning.

Three conveyor speeds can be selected through the control panel by the operator and customized on-site.

All internal components: wash and rinse arms, tank filters, curtains can be easily removed for cleaning.

Built-in WASH-SAFE CONTROL system raises water temperature to 85°C to sanitize the rinse water. No external boiler is required. Built-in air break and rinse booster pump ensure constant temperature and pressure throughout the rinsing cycle regardless of the inlet water condition.

Built-in drain valve in the tanks allows automatic dump and fill to refresh the water in the tank without any interruption of the washing process.

Automatic drain, clean and sanitize cycles featured as standard. The internal chamber, is completely cleaned or sanitized avoiding bacteria proliferation for maximum hygiene and reducing manual work/time for operator.

CLEAR BLUE filtering system removes soil from the wash water providing cleaner water and highly active detergent thus ensuring better washing performance and lower running costs.

Maximum capacity per hour of 250 racks easy to switch to DIN 10510 compliant or other speed.

Unit equipped with USB port making it simple to read data such as machine identification, counters and consumption, components, devices and alarm logs. Machine parameters can be uploaded and downloaded and firmware updated.

Intuitive touch screen control panel features user-friendly display to easily operate the machine and to monitor machine status. Three different levels of interaction are available each show relevant messages and information to the operator, the general maintenance staff and the authorized service partners.

The unit is ready to be connected with OnE Connectivity for 24/7 real time monitoring, increasing equipment uptime, maximum profit and optimizing your process.

Pre-wash section uses cold water so food remains are not "baked" onto the plates in order to have better pre-wash performance.

Large counter balanced inspection door allow unrestricted all-round access to the wash and rinse area. Door is insulated with injected foam. This adds strength as well as reduces noise and heat loss.

Sustainability

Automatic back-up mode is activated when a failure occurs. Guided troubleshooting for fast fixes including 150 precises notifications and 23 easy-to-follow processes.

Built-in Energy Saving Device (ESD) captures the hot steam released on the sides of the machine to heat up incoming cold water before entering to the boiler, thus saving energy and reducing heat emission from the machine.

Dual rinse with air break and rinse booster pump guarantees rinse water consumption of 1.0 liters/rack regardless of inlet water pressure to ensure low energy, water, detergent and rinse aid consumption.

Self-draining vertical wash pumps provide maximum hygiene.

Built-in stabilized pressure valve ensures constant pressure throughout the rinsing cycle regardless of inlet water pressure.

Auto-start/stop equipped in different zones ensures that the zone runs only when a rack is passing through it. This reduces water, energy, chemical consumption and noise.

ZERO LIME Device as a fully automatic cycle ensures total scale removal from the boiler, the hydraulic circuit, the washing chamber and the rinsing chamber allowing ultimate performances and lower energy consumption thanks to highly efficient heating elements.

All chambers without internal pipes and therefore no hidden dirt traps.

Construction

All electric components are put in one IP65 central box isolated from water and steam to ensure high reliability.

Dishwasher structure is held together with a solid 50 x 50 mm stainless steel frame to provide long-term sturdiness.

External pre-arrangement for inlet water, drain water, detergent & rinse aid connections for fast and easy installation on both sides of the unit.

All main components made in heavy duty anti-corrosive 304 type stainless steel: external front, side panels and internal chambers, wash and rinse arms, doors and rack transportation system.

Modularity design allows the machine not only be disassembled for delivery and re-assembled at customer’s site, but also to be customized and upgraded on-site and over time.

Deep drawn pressed wash tank with fully rounded corners, sloped towards the drain to prevent dirt buildup, provides fast drainage in just a few minutes. With no welding points the pressed tank offers a guaranteed water tight solution.

Included Accessories

Image

Quantity

Code

Description

Quantity: 2

Code: 865498

Splash hood kit for single and dual rinse Rack Type Dishwasher, 200 mm

Quantity: 1

Code: 922421

IoT module for OnE Connected (Combi Ovens, Blast chiller/freezers, Rack Type DW) and SkyDuo (one IoT board per appliance - to connect oven to blast chiller for Cook&Chill process).

Complete the form below to request more information

Let us provide more for
your business!

Your browser is out-of-date!

Update your browser to view this website correctly. Update my browser now

Compare Products 0/4 x

Compare Products

Dual Rinse Rack Type dishwashers - 250 racks per hour